Thick Anti-Slip Mat (275-0120)
These high friction mats are cuttable and compressible. Use for adding grip, friction, or padding. Size: 12 inch x 15 inchMaterial: Black Rubber over Silk Mesh ..
Thin Anti-Slip Mat (275-0121)
  These high friction mats are cuttable and compressible. Use for adding grip, friction, or padding. Size: 12 inch x 15 inch"Material: Black Rubber over Silk Mesh ..
Pneumatics Kit 1 - Single Acting Cylinders (275-0274)
Pneumatic cylinders use compressed air (rather than motors) to produce motion that rests in one of 2 states: fully extended or fully retracted. The cylinder in Pneumatics Kit 1 is single-acting -- it uses air to extend the cylinder rod, but uses a spring to return to its contracted state. As a res..
Pneumatics Kit 1A - Single Acting Cylinder Add-On (275-0275)
Kit 1A adds one Cylinder (Air Push, Spring Return) to Kit 1 or Kit 2Cannot be used without Kit 1 or Kit 2Kit Includes: (1) Solenoid Driver - Cable w/Driver, Connects one VEX EDR I/O Port to one Solenoid (1) "T" Fitting - "T" Fitting for Valves - KQ2T04-00 or "-00A" (1) Cylinder - Si..
Pneumatics Kit 2 - Double Acting Cylinders (275-0276)
Kit 2 is a complete pneumatics add-on for VEX EDR. The cylinders are Double Acting, meaning they use air pressure to extend and retract the piston.Uses one VEX EDR Controller I/O port per air cylinderReservoir is filled using a standard tie pump Kit Includes: (2) Solenoid Driver - Cable w/Dri..
Pneumatics Kit 2A - Double Acting Cylinder  Add-On (275-0277)
Kit 2A adds one Cylinder (Bi-directional) to Kit 1 or Kit 2. Add-on Kit. Double Acting Cylinders. Cannot be used without Kit 1 or Kit 2.Kit Includes: (1) Solenoid Driver - Cable w/Driver, Connects one VEX EDR I/O Port to one Solenoid (1) "T" Fitting - "T" Fitting for Va..
Pneumatics Tubing (5 ) (275-0447)
    5ft. of Polyurethane Tubing for use with VEX Robotics Pneumatics. (Black, 5/32" OD) 5ft. of Polyurethane Tubing. Compatible with VEX Robotics Pneumatics. ..
Drive Shaft Bar Lock (8-pack) (275-1065)
Metal version of the shaft locking part. Three locations for square shafts. Very strong. Made from cold rolled steel, 0.046" thick, zinc plated. Sold in packs of 8. Technical Specifications Downloads STEP File Materi..
Nylon Spacer Variety Pack (275-1066)
  A spacer is used to create a space between two objects, often to properly position them.  They eliminate slop on shafts, add space between metal parts and are made of plastic and nylon. Variety pack includes:(10) 0.125" Nylon Spacer(10) 0.250" Nylon Spacer(10) 0.375" Nylon Spacer(..
1/2 Thumbscrew (50-pack) (275-1485)
These plastic thumbscrews are the same size (8-32) as standard VEX screws only they have a 0.428" diameter knurled head so they can be tightened or loosened by hand.  Great for applications where a screw will be inserted or removed multiple times, such as robot access panels or battery mou..
Bearing Flat (10-pack) (276-1209)
(10) Bearing FlatsMaterial:  AcetalGive your motors something to turn with VEX EDR Drive Shafts. Use Bearings and Shaft Collars to keep your mechanisms and wheels moving smoothly, and locked into place.  Use spacers if certain parts of your robot need to be properly positioned, or you need..
Mecanum Wheel 4  (4-pack) (276-1447)
Mecanum wheels allow savvy robot designers to create drivetrains capable of moving in any direction using a standard chassis shape. Simply power each wheel with a different motor and by changing the directions the wheels spin get your robot to move in different directions! Allows r..
4  High Traction Tire (4-pack) (276-1489)
Upgrade your tires. The VEX 4" High Traction Tires are replacements for the "all-purpose" treads found on VEX 4" diameter wheels. These tires are designed to provide high traction on smooth surfaces.  Use with 4" VEX Wheels *Note: Wheel rims not included. Simply remove the current 4..
2.75" Wheel (4-pack) (276-1496)
(4) 2.75" diameter wheels.  Removing the tread of the 2.75" wheel reveals a low-friction wheel that can be used for other purposes. Offered in multiple sizesHigh traction tire profileVersatile wheel inserts for a variety of applicationsTread is made of rubber and wheel is ABS plastic  ..
4 Wheel (4-pack) (276-1497)
Traction Wheels offer optimal grip on soft surfaces like the foam tiles used in the VEX Robotics Competition.  There are versatile wheel inserts for a variety of applications. Removing the tread of the 4" wheels reveals a ribbed plastic wheel.Pack includes: (4) 4" Diameter Traction Whee..
Intake Roller (8-pack) (276-1499)
Intake rollers are specifically designed for ball intake systems.  The flexible rubber fingers grip the ball.  The fingers also deflect, allowing for ball size variation.•Available in a (2) or (8) pack.•Rubber fingers.•Hard plastic center with square hole. ..
Winch and Pulley Kit (276-1546)
This kit provides the ability to implement a winch and pulley system and create block and tackle mechanisms to utilize mechanical advantage.•Lift, lower, hang, drag and more.•Configurable for many applications.•Ratchet and Pawl can be engaged to prevent back driving.Kit Includes:(1) Winch Bracket(1)..
Turntable Bearing Kit (276-1810)
The VEX Turntable Bearing Kit provides two options for low friction, high load rotational joints. These are especially well suited for rotational joints with lots of side load - this kit makes it easy to build a turret on your robot! Integrated gearing makes each turntable simple to actuate whi..
2.75"  Omni Directional Wheel - Double Roller (2-pack) (276-1902)
Omni-Directional wheels roll forward like normal wheels, but slide sideways with almost no friction (no skidding during turns). Use these wheels to make your robot turn smoothly or build a holonomic drivetrain. 2.75" diameter 14 rollers per wheel   Technical Spe..
Linear Motion Kit (276-1926)
Push & Pull The Linear Motion Kit provides a method for VEX builders to create linear mechanisms. Utilize the low friction slide rails for your own mechanisms or combine them with included Rack Brackets and VEX Rack Gears (not included) to build direct driven linear actuators. Each of the plasti..
Pillow Block Bearing & Lock Bar Pack (276-2016)
Bearing Blocks mount on a piece of structure and supports a shaft which is offset either above, below, or to the side of the structure. Lock Bars allow any VEX component to be “locked” to a shaft so that it will spin with the shaft. Note: These items are not sold separately...
Plastic Spacer, 4.6mm (20 pack) (276-2018)
20 pack Plastic Spacers, 4.6 mmA spacer is used to create a space between two objects, often to properly position them. Available in various lengths. Eliminate slop on shafts. Add space between metal parts. Plastic and Nylon options    ..
Plastic Spacer, 8mm (20-Pack) (276-2019)
A spacer is used to create a space between two objects, often to properly position them.  This pack includes (20) 8mm Plastic Spacers.  Spacers are compatible with all VEX screws and shafts. • Eliminates slop on shafts.• Adds space between metal parts.• Made of Plastic and Nylon. ..
3-Wire Servo (276-2162)
Servo motors are a type of motor that can be directed to turn to face a specific direction, rather than just spin forward or backward. Expand functionality Add pan and tilt to a camera 100 degrees of rotation Do exact positioning   Technical Specific..
Sprocket & Chain Kit (276-2166)
The Sprocket & Chain Kit includes five different sprocket sizes that allow for a variety of ratios, and 4 feet of chain. Great for any application where you need to transfer power across long distances.  It is designed to carry moderate loads. Every section of chain is a master link.Kit Inc..
Tank Tread Kit (276-2168)
Build all terrain robots! This kit contains over five feet of tank tread designed specifically for the VEX Robotics Design System. Use this tank tread to build robot tracks which can overcome tough terrain, or build a conveyor belt for scooping up objects. Climb over obstacles. ..
Gear Kit (276-2169)
This kit contains four sizes of VEX Spur Gears (12-, 36-, 60-, and 84-tooth gears). The 60- and 84-tooth gears have extra mounting holes for attaching metal bars or parts to these gears when using them as part of a turntable system or similar design. Create robot transmissions, gea..
Additional High Strength Chain (276-2172)
High Strength Sprockets and Chain allow for higher loads to be transmitted across long distances. The Sprockets come in five different sizes, allowing for numerous ratios to best suit your needs. The High Strength and Sprockets are also capable of lifting up to 50 pounds, so make sure to use them..
2-Wire Motor 393 (276-2177)
Drive on. The 2-Wire Motor 393 is the primary actuator used in the VEX Robotics Design System. Build rotational mechanisms, drive bases, rotational joints, conveyor belts - anything that spins can be built using the 2-wire Motor 393. Strong, steel internal gears. Can be configur..
Advanced Gear Kit (276-2184)
Gears are one of the primary sources of power transmission in VEX EDR. We offer a variety of both normal and high strength gears, that come in a multitude of shapes and sizes. Start with a simple project like building a gear reduction, and work your way up towards building more complex mechanism suc..
4  Omni-Directional Wheel (2-pack) (276-2185)
As the name suggests, an Omni-Directional Wheel can travel in more than one direction. When the axle spins, it behaves like a normal wheel. However, you’ll notice that there are rollers all around the outer circumference. These rollers allow the wheel to travel sideways as well.Omni-Directional w..
Motor Controller 29 (276-2193)
The VEX Motor Controller 29 uses a standard PWM signal (like that originating from the 3-wire ports on VEX Microcontrollers) to drive a VEX 2-Wire Motor.Note: We recommend using no more more than one (1) 3-Wire extension cable in between the Motor Controller 29 and a VEX Microcontroller. For longer ..
Claw Kit (276-2212)
Grab and Manipulate Objects With the VEX Robotics Claw Kit, your robot can easily grab and manipulate various objects. Motor required and not included. Strong enough to hold a 12 oz soda can. Dexterous enough to grab a feather. Comes partially assembled. Compatible..
Tank Tread Upgrade Kit (276-2214)
These upgrade links should be useful to designers wishing to create more advanced mechanisms utilizing the tank tread. Different Tread-Links Increase Functionality. Get High-Traction on Smooth Surfaces. Compatible with Tank Tread Kit, High Strength Chain & Sprocket..
Bearing Attachment Rivet (50-pack) (276-2215)
These make mounting Flats Bearing onto VEX structural component easy. Reusable; simply push the pin out from the back side. Speed up robot assembly. 50 ea of the Bearing Pop Rivets. Reusable.   Technical Specifications Compatibility ..
6  Wheel Leg (4-pack) (276-2218)
Create robots capable of climbing over almost any obstacle. The Wheel Legs are great for constructing All-Terrain or Off-Road robots. These legs consist of (4) spoke "legs" protruding from a central hub with mounting holes for attaching mechanisms. They also have high traction rubber feet and a..
Booster Kit (276-2232)
This Top Recommended Add-On Kit includes pieces specifically recommended by VEX builders to maximize versatility. Contains over 600 pieces of VEX Structural and Motion Components. (1)Steel Chassis 25x25x2 (14)Steel Plates & Bars (6)Steel Angles (6)Steel C-C..
High Strength Gear Kit (276-2250)
Gears are one of the primary sources of power transmission in VEX EDR. We offer a variety of both normal and high strength gears, that come in a multitude of shapes and sizes. Start with a simple project like building a gear reduction, and work your way up towards building more complex mechanism suc..
Metal 12-Tooth Pinion (12-pack) (276-2251)
(12) High Strength 12-tooth Gear (0.58 inch diameter)(12) 12-Tooth Pinion Gear Inserts..
High Strength Sprocket & Chain Kit (276-2252)
Reinforced High Strength Sprockets can transmit higher loads over long distances. Use this kit to withstand higher stresses and  lift heavier loads. Useful for any application where regular chain just won't cut it.  The High Strength Design enables lifts up to 50 lbs.  Use with H..
8-32 x 0.125  Setscrew (32-pack) (276-2385)
  These 8-32" x 0.125" setscrews fit in VEX Shaft Collars. Use them as replacements or spare parts." 8-32 thread. Use 5/64 Allen to tighten.   Technical Specifications Kit Contents (32) 8-32 x 0.125" Setscrews Compatibility ..
Motor 393 Refurb Kit (276-2487)
Lose your gears? This convenient replacement gear pack for the 2 Wire Motor 393 (only) will get you going again without having to purchase a new motor. Includes one full set of gears.Kit Includes:•(1) High Speed Gear Set•(1) High Torque Gear Set•(1) Set of replacement case assembly screws&nb..
Universal Joint (5-pack) (276-2723)
  Universal joints provide a mechanical link between two intersecting, non-parallel shafts. Each side of the VEX U-Joint includes a socket for a VEX square shaft, and a set-screw to hold the shaft in place. Create complex robot mechanisms Transfer power "around corners" and at angl..
High Strength 84-tooth Gear (4-pack) (276-3438)
84-tooth gears have extra mounting holes for attaching metal bars or parts to these gears when using them as part of a turntable system or similar design.  Create robot transmissions, gearboxes, and gear reductions, vary the speed or torque of robot motion systems and increase design possibilit..
High Strength Clamping Shaft Collar (10-Pack) (276-3520)
High Strength Shaft Collars are designed to fit onto High Strength Shafts. This clamping-style collar uses standard VEX EDR button head screws and nuts to maintain a tight lock without scratching or damaging the shaft.•Designed specifically for VEX EDR High Strength Shafts•Standard VEX EDR screws us..
High Strength Shaft Bearing (10-Pack) (276-3521)
The High Strength Shaft Bearing is a larger version of the Bearing Flat that is designed for the 0.25" High Strength Shafts. VEX EDR 2", 3", and 4" High Strength Shafts are actually designed about 1mm shorter than their respective 2", 3", and 4" 8-32 Standoffs.  This means that if you use stand..
High Strength Shaft 3" Long (4-Pack) (276-3522)
High Strength Shaft 3" Long (4-Pack) VEX EDR High Strength Shafts and hardware are specifically designed for those applications that typical shafts just can't handle. Use these shafts in high-torque or high-impact situations, and never worry about your gearbox or intake breaking again. ..
High Strength Shaft 4" Long (4-Pack) (276-3523)
Larger 1/4" shafts are tougher, stronger, and ready for even the most stressful robotic applications. These thicker shafts are less resistant to both twisting and bending fatigue, meaning that you should have no fear of designing high-torque gearboxes or high-impact drivetrains. Works with a..
High Strength Shaft 12" Long (4-Pack) (276-3524)
Larger 1/4" shafts are tougher, stronger, and ready for even the most stressful robotic applications. These thicker shafts are less resistant to both twisting and bending fatigue, meaning that you should have no fear of designing high-torque gearboxes or high-impact drivetrains. Works with all&nbs..
3.25" Traction Wheel (4-Pack) (276-3525)
A pack of (4) of the VEX 3.25" diameter wheels. These wheels include a tire designed for optimal grip on soft surfaces like the foam tiles used in the VEX Robotics Competition. Removable wheel inserts allow for additional versatility - use these wheels with either standard Drive Shafts or High Stren..
3.25" Omni-Directional Wheel (4-Pack) (276-3526)
Omni-Directional wheels roll forward like normal wheels, but slide sideways with almost no friction (no skidding during turns). These wheels are the same size as the VEX 3.25" Traction Wheels. Removable wheel inserts allow for additional versatility - use these wheels with either standard Drive ..
393 Motor Turbo Gear Set (4-pack) (276-3527)
Use the Turbo Gear Set to push your motors to the fastest speeds ever seen in VEX robotics. This gear pack replaces the gears inside a 2-Wire Motor 393 for high-RPM, low-torque applications. Only for 2-Wire Motor 393 240 RPM output speed is 140% faster than standard gearing Use with ex..
High Strength Sprocket 6 Tooth (8-Pack) (276-3876)
High Strength Sprocket 6 Tooth (8-Pack)High Strength Sprockets and Chain allow for higher loads to be transmitted across long distances. The Sprockets come in five different sizes, allowing for numerous ratios to best suit your needs. The High Strength and Sprockets are also capable of lifting up to..
High Strength Sprocket 12 Tooth (4-Pack) (276-3877)
These reinforced sprockets and chain can transmit higher loads over long distances. Use this kit to withstand higher stresses and lift heavier loads. Useful for any application where regular chain just won't cut it. High Strength Design - lift up to 50 lbs 12 Sprockets in 5 Sizes ..
High Strength Sprocket 18 Tooth (4-Pack) (276-3878)
High Strength Sprocket 18 Tooth (4-Pack) High Strength Sprockets and Chain allow for higher loads to be transmitted across long distances. The Sprockets come in five different sizes, allowing for numerous ratios to best suit your needs. The High Strength and Sprockets are also capable of lifting up ..
High Strength Sprocket 24 Tooth (4-Pack) (276-3879)
High Strength Sprocket 24 Tooth (4-Pack)High Strength Sprockets and Chain allow for higher loads to be transmitted across long distances. The Sprockets come in five different sizes, allowing for numerous ratios to best suit your needs. The High Strength and Sprockets are also capable of lifting up t..
High Strength Sprocket 30 Tooth (4-Pack) (276-3880)
High Strength Sprocket 30 Tooth (4-Pack)High Strength Sprockets and Chain allow for higher loads to be transmitted across long distances. The Sprockets come in five different sizes, allowing for numerous ratios to best suit your needs. The High Strength and Sprockets are also capable of lifting up t..
High Strength Shaft Insert Kit (276-3881)
Removable High Strength Shaft Inserts for High Strength Gears and some wheels that allow for versatility in user application. Switch from a driven gear (square hole) to a free spinning one (round hole) in seconds.•Increased versatility during design and construction•Free spinning plastic and high st..
Clamping Shaft Collar (10-Pack) (276-3891)
Shaft Collars lock to drive shafts, keeping wheels and gears from sliding along the shaft. Collars fit around Drive Shafts and can be fastened in place using a setscrew.•Designed specifically for VEX EDR Drive Shafts•Set screw uses the same Hex Key as the 6-32 Motor ScrewsIncludes:•(10) Clamping Sha..
Linear Motion Additional Truck Kit (276-4489)
Spare plastic trucks from the VEX EDR Linear Motion Kit. Includes:(8) Inner Slide Trucks(8) Outer Slide Trucks. ..
Rack Gear v2 (16-pack) (276-4782)
Rack Gears can be used to turn rotary motion into linear motion.•Use any VEX spur gear as a pinion to drive these rack gears. •Stack multiple rack gears back to back for longer motions.•Combine these with a VEX linear slide and Rack Gear Bracket (sold separately) to create a simple linear actuator.N..
High Strength 36-Tooth Gear (8-pack) (276-5034)
Build mechanisms capable of achieving higher torque or speed than ever before - lift heavier loads and survive bigger impacts with the additional gear ratio options provided by the largest high strength gear available. Works with the VEX High Strength Gear Kit or any VEX spur gear.  ..
High Strength 60-Tooth Gear (8-pack) (276-5035)
Build mechanisms capable of achieving higher torque or speed than ever before - lift heavier loads and survive bigger impacts with the additional gear ratio options provided by the largest high strength gear available.  Works with the VEX High Strength Gear Kit or any VEX spur gear. D..
0.375" OD Nylon Spacer Variety Pack (276-6340)
Because that wheel isn't going to drive itself. Give your motors something to turn with VEX EDR Drive Shafts.Want a smoother ride? Use Bearings and Shaft Collars to keep your mechanisms and wheels moving smoothly, and locked into place.Use spacers if certain parts of your robot need to be properly p..
Showing 1 to 64 of 64 (1 Pages)